This topic covers the hardware aspects of the Q-SYS DataPort Card. For detailed information about the functionality of the DataPort Card, refer to the DataPort topic.
Type 2 hardware provides new cables and connectors between the I/O cards and main boards in Cores and I/O Frames. Due to this change, the Type 2 hardware is not physically compatible with the older hardware. You can still integrate the new I/O Frames and Cores in the same system with older hardware, but the I/O cards are not interchangeable. Type 2 hardware can be identified by a yellow label on the back of the Core and I/O Frame, and the bottom of the I/O cards.
IMPORTANT: DataPorts on multi-port amplifiers must be wired to DataPorts on the same I/O Frame or Core. You cannot wire some of the amplifier's DataPorts to a Core and others, on the same amplifier, to an I/O Frame. You cannot wire some of the amplifier's DataPorts to one I/O Frame and others, on the same amplifier, to another I/O Frame.
|
DataPort (CODP4) |
||
|---|---|---|
Dynamic range |
un-weighted |
> 114 dB |
|
A-weighted |
> 117 dB |
|
|
|
||
Distortion
|
+4 dBu (max) |
— |
|
2 dB below clip (max) |
< 0.04% THD+N |
|
|
|
||
Crosstalk
|
Inter-channel (max) |
> 95 dB |
|
Inter-channel (typ) |
> 100 dB |
|
|
Intra-channel (max) |
> 100 dB |
|
|
Intra-channel (typ) |
> 110 dB |
|
|
|
||
Frequency Response |
20Hz - 20 kHz (max) |
± 0.5 dB |
|
20Hz - 20kHz (typ) |
± 0.2 dB |
|
|
|
||
Input Impedance |
Balanced (nominal) |
— |
|
Unbalanced (nominal) |
— |
|
|
|
||
Common Mode Rejection |
20Hz - 20kHz (Min) |
— |
|
20Hz - 20kHz (Typ) |
— |
|
|
|
||
Input Sensitivities |
Vrms |
— |
|
dBu |
— |
|
|
dBv |
— |
|
|
|
||
Mute |
Electro-mechanical relays |
Infinite Attenuation |
|
|
||
Audio ConvertersGroup Delay (at 48 kHz) |
Analog to Digital Conversion (ADCs) |
— |
|
Digital to Analog Conversion (DACs) |
24-bit delta-sigma at 48 or 96 kHz sample rate |
|
|
Output |
0.25 ms |
|
|
|
||
Connectors |
|
Two DE-15 (female 15-pin high-density D shell) connectors |
|
|
||
User-configurable Options(software enabled) |
Phantom Power |
— |
|
Input Sensitivity |
— |
|
|
Output Trim Vrms (max) dBu (max) dBv (max) |
— — — |
|
|
Amplifier Standby |
Set or clear amplifier in standby mode |
|
|
Mute |
Set or clear individual channel mutes |
|
|
Enable Meters |
Enable data collection of meters for each channel |
|
|
Audio Output Levels |
Adjust individual audio channel levels |
|
|
|
||
Amplifier Model Support |
|
CX, PowerLight™ 3 Series, DCA, and legacy V1 models |
© 2009 - 2016 QSC, LLC. All rights reserved. QSC and the QSC logo are trademarks of QSC, LLC in the U.S. Patent and Trademark office and other countries. All other trademarks are the property of their respective owners.
http://patents.qsc.com.
Related Topics